雙組份打膠機的注意事項
1.由于雙組份密封膠的固化需要一定時間，因此，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. because the curing of the two component sealants takes a certain time, the glass coated with two components of sealant should be moved gently.
2.A組、B組份膠應保持清潔，嚴防異物進入膠中。
Group 2.A and B components should be kept clean and prevent foreign substances from entering the glue.
3.在連續工作過程中，膠槍每次停止工作時間一般不得超過20分鐘，否則，應用A組份膠沖出全部混合膠，直單一的A組份膠從槍口排出為止。
3. in the continuous working process, the glue gun will not stop working more than 20 minutes each time. Otherwise, all the mixed glue is washed out with A component glue until the single A component is discharged from the muzzle.
4.高壓膠管不得強行擠壓、彎曲，防止影響系統正常工作。
4. high pressure hose should not be forced to bend or bend to prevent the system from functioning normally.
5.混膠器應經常保持暢通，以保證良好的出膠效果。如遇堵塞情況，可用丙酮浸泡后清洗。建議每5組清洗一次。
5. rubber mixer should be kept smooth to ensure good glue production. In case of blockage, acetone can be soaked and cleaned. It is suggested that every 5 groups be cleaned once.
6.當膠槍長時間不用時，應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
6. when the rubber gun is not used for a long time, the gun body should be removed and the residual colloid in the rubber gun and the rubber mixer should be cleaned with solvents.
7.不同雙組份膠生產廠家所生產的膠內含雜質數量不同，根據實際情況清晰B組分的過濾網及單向止回閥，建議每?jī)山M清洗一次。
7. the number of impurities in the rubber produced by the different double component rubber manufacturers is different. According to the actual situation, the filter net and the one-way check valve of the B component are clear. It is suggested that every two groups be cleaned once.
8.任何因膠體固化所造成的膠槍、管路或整機的故障，一律不在保修范圍之內。
8. any failure of glue gun, pipe or whole machine caused by gel solidification is not within the scope of warranty.
希望上述介紹對您有所幫助哦，我們以真誠貼近客戶，以行動滿足客戶，以雙贏保有客戶，以個性客戶，您的滿意是我們大的追求。
I hope that the introduction will help you, we are sincere close to the customer, to meet the customers by action, to win a win-win customer, to lead the customer with personality, your satisfaction is our greatest pursuit.
上一篇：雙組份打膠機的注意事項
下一篇：中空玻璃打膠機生產效率高不高？
