雙組份打膠機機頭不在原位怎么調？
雙組份打膠機機頭不在原位怎么調？
濟南雙組份打膠機廠家提醒您，可以先連接電源，然后在控制面板上操作，然后在做調整。具體操作流程是：
How to adjust if the head of two-component sealant dispenser is not in place? The manufacturer of Jinan two-component sealant dispenser reminds you that you can connect the power supply first, then operate it on the control panel, and then make adjustments. The specific operation process is as follows:
1、放在一個平整干凈的平面上，連接電源和氣源，兩者確認接通之后就開始進行操作。
1. Put it on a flat and clean surface, connect the power supply and air supply, and start the operation after they are confirmed to be connected.
2、打膠機中間會有一個混膠過程，在供膠機上面混膠完畢之后，需要在電子顯示屏上控制面板上進行選擇行走設置。在機頭停止時，打開機頭上面B膠閥門，接著在控制面板上找到Esc鍵返回主界面，然后F2狀態設置，在打開界面后按K3鍵供膠開始，當膠嘴中完全混合的膠流出按K4鍵結束供。
2. There will be a glue mixing process in the middle of the glue feeder. After the glue is mixed on the glue feeder, you need to select the walking setting on the control panel on the electronic display screen. When the handpiece stops, open the B glue valve on the handpiece, find the Esc key on the control panel to return to the main interface, and then set the F2 status. After opening the interface, press the K3 key to start glue supply, and press the K4 key to end glue supply when the glue completely mixed in the nozzle flows out.
3、需要記住的是工作結束之后或者在較長時間不工作時，需要沖洗混膠裝置，防止供膠管的堵塞，影響未來使用效果。
3. It should be remembered that after the work is completed or when the machine is not working for a long time, the rubber mixing device needs to be flushed to prevent the rubber supply pipe from being blocked and affecting the future use effect.
4、調整環節，吸盤調整，涂膠機吸盤與旋轉臺的高度調整合適。
4. The adjustment link, suction cup adjustment, and the height adjustment of the glue applicator suction cup and the rotary table are appropriate.
5、氣動開關、膠嘴、探針調整，將事先合好的中空玻璃放在旋轉臺上，靠近涂膠機工作面，然后中空玻璃推到定位上，調整膠嘴與玻璃的高度，使出膠嘴的出膠口語鋁槽在同一個水平線上，膠嘴與玻璃之間的頂力合適，鋁槽深度檢測探針與出膠口線在統一水平線上。
5. Adjust the pneumatic switch, rubber nozzle and probe. Put the previously closed insulating glass on the rotary table close to the working face of the glue applicator, and then push the insulating glass to the position. Adjust the height of the rubber nozzle and the glass, so that the center of the aluminum groove at the rubber outlet of the rubber nozzle is on the same horizontal line, the jacking force between the rubber nozzle and the glass is appropriate, and the aluminum groove depth detection probe and the center line of the rubber outlet are on the same horizontal line.
6、啟動開關機頭的非常前端的光開關與玻璃之間的檢測距離1.5~2mm。在控制面板上選擇狀態設置，打開狀態設置后選擇吸盤開K5鍵，此時機頭會往前移動，如果不往前移動則檢查并調整啟動開關的檢測距離。
6. The detection distance between the optical switch at the very front end of the starting switch head and the glass is 1.5~2mm. Select the status setting on the control panel. After opening the status setting, select the K5 key of the suction cup. At this time, the machine head will move forward. If it does not move forward, check and adjust the detection distance of the start switch.
This is the way to adjust the two-component sealant dispenser head when it is not in place. Do you have anything to ask about it? Welcome to our website http://www.zkty.org.cn Get to know more!
上一篇：打膠機呈現花膠以及打膠不豐滿的原因
下一篇：雙組份打膠機換桶的操作細節
